Return to Home Page	To Company Store
DIY Test Equipment	Chip Amplifiers
DIY Power Supplies	DIY Audio Designs

Links:
HP3577 Display Formats By Alpha   Math Function Minus - percent % Math Bracket ( Math Bracket ) Math Function Multiply * Math Function Divide / Math Function Plus + Math Term for Input A A Attenuation A = 0 dB AA1 Attenuation A = 20 dB AA2 Attenuation B = 0 dB AB1 Attenuation B = 20 dB AB2 Start Amplitude (Entry) AMA Stop Amplitude (Entry) AMB Amplitude AMP Annotation Off AN0 Annotation On AN1 Annotation Clear ANC Aperture 0.5% of Span AP1 Aperture 1.0% of Span AP2 Aperture 2.0% of Span AP3 Aperture 4.0% of Span AP4 Aperture 8.0% of Span AP5 Aperture 16% of Span AP6 Attenuation R = 0 dB AR1 Attenuation R = 20 dB AR2 Autoscale ASL Amp Step Size AST Attenuation ATT Auto Bandwidth Off AU0 Auto Bandwidth On AU1 Averaging Off AV0 Average N = 4 AV1 Average N = 8 AV2 Average N = 16 AV3 Average N = 32 AV4 Average N = 64 AV5 Average N = 128 AV6 Average N = 256 AV7 Average AVE Math Term for Input B B Bus Diagnostics Mode Off BD0 Bus Diagnostics Mode On BD1 Beeper Off BP0 Beeper On BP1 Resolution BW 1 Hz BW1 Resolution BW 10 Hz BW2 Resolution 100 Hz BW3 Resolution 1kHz BW4 Measurement Calibration CAL Continouous Entry (knob) Off CE0 Constinuous Entry (knob) Onn CE1 Measurement CAL Full CFL Frequency, FRC Step Size (Entry) CFS Measurement CAL Continue CAL CGO Characters Off CH0 Characters On CH1 Clear Keyboard Buffer CKB Centimeters CM Marker Coupling Off CO0 Marker Coupling On CO1 Copy Input CPI Measurement Cal Partialize CPR Copy Scale CPS Configure Plot Menu CPT Clear Trip, Receiver CTR Clear Trip, Source CTS Dump Average Number DAN Delay Aperture Menue DAP dBm DBM dB Relative DBR dBV DBV Dump Characters DCH degrees DEG TraceOff DF0 Delay DF1 Imaginary DF2 Real DF3 Polar DF4 Phase DF5 Linear Magnitude DF6 Log Magnitude DF7 Define Function DFC Define Math DFN Scale/DIV DIV Dump Key or Knob DKY Dump Marker n DMn Dump Status DMS Dump Register x (x= A, B, R, D1, D2, D3, D4) DRx Display Function DSF degrees/span DSP Display Memory Test DST Dump Trace n DTn Display Test Pattern DTP exponent E Exponent E Enter Annotation ENA Enter Graphics ENG Enter Menu (User Defined) ENM Error Reporting Mode n Ern Math Term for Function F ASCII Data Format FM1 64 Bit IEEE Data Format FM2 32 Bit HP 3577B Binary FM3 Fast Processor Test FPT Frequency, Start Frequency FRA Frequency, Stop Frequency FRB Frequency, Center Frequency FRC Frequency FRQ Frequency, Span FRS Freq Step Size FST Full Sweep FSW Full Sweep FSW Graticule Off GR0 Graticule On GR1 Smith Chart Off GT0 Smith Chart On GT1 Plotter Address (Entry) HBP Entry Off HLD Function HP-IB Code Input = S11 I11 Input = S12 I12 Input = S21 I21 Input = S22 I22 Impedance A = 50 Ohms IA1 Impedance A = 1 M Ohm IA2 Input =A/R IAR Impedance B = 50 Ohms IB1 Impedance B = 1 M Ohm IB2 Input=B/R IBR Dump Instrument ID ID? Input=D1 ID1 Input=D2 ID2 Input=D3 ID3 Input=D4 ID4 Increment Down (Down Arrow) IDN Input INP Input x= R,A,B Inx Instrument Preset IPR Impedance R = 50 Ohms IR1 Impedance R = 1 M Ohm IR2 Increment (Up Arrow) IUP Math Term for constant K Define Math, Constant K1 Imaginary (Entry) KI1 Define Math, Constant K2 Imaginary (Entry) KI2 Define Math, Constant K3 Imaginary (Entry) KI3 Define Math, Constant K1 Real (Entry) KR1 Define Math, Constant K2 Real (Entry) KR2 Define Math, Constant K3 Real (Entry) KR3 Length A Off LA0 Lentth A On LA1 Length B OFf LB0 Length B On LB1 Load Register x (X= D1 D2 D3 D4) LDx Length LEN Load State (learn mode in ) LMI Dump State (learn mode out) LMO Length A (Entry) LNA Length B (Entry) LNB Length R (Entry) LNR Length Step Size LNS Length R Off LR0 Length R On LR1 Load Register x (X= A B R) LRx Manual Amplitude Entry MAM Meters MET Manual Frequency Entry MFR Marker Off MK0 Marker Offset (Entry) MK0 Marker On MK1 Marker MKG Marker Position (Entry) MKP MKR-Left for Target MLT Polar Marker Units (Mag/Phase) MMP Menu Off MN0 Menu On MN1 Menu Clear MNC Marker Offset Off MO0 Marker Offset On MO1 Marker Offset Map (Entry) MOA Marker Offset Freq (Entry) MOF More Serv Diag Menu MOR MKR Offset Span MOS MKR-Polar Phase Ref MPF Dumper Marker n Position MPn Polar Marker Units (Real/Imag) MRI MKR-Right for Target MRT milliseconds MSC milliseconds MSC Sweep Time, Sample Time MSR MKR-Start Frequency MTA MKR-Stop Frequency MTB MKR-Center Frequency MTC Marker to Manual MTM MKR-Min MTN MKR-Full Scale MTP MKR-Reference Level MTR MKR-Target Value MTV MKR-Max MTX milliVolts MV Measurement Cal Normalize NRM Measurement Cal Short NRS Number of Steps =6 NS1 Number of Steps = 11 NS2 Number of Steps = 21 NS3 Number of Steps = 51 NS4 Number of Steps = 101 NS5 Number of Steps = 201 NS6 Number of Steps = 401 NS7 nanoseconds NSC Nanoseconds NSC Steps/Sweep Menu NST nanoVolts NV Polar Full Scale (Entry) PFS Graticule Pen Number PGP Polar Imag Offset (Entry) PIO Plot All PLA Plot Characters PLC Set Plot Config to Default PLD Plot Graticule PLG Plot Menu PLM Plot Trace n PLn Plot Trace Marker n PMn Polar Mag Offset (Entry) PMO Pen Speed Fast (Max) PNM Pen Speed Slow PNS Polar Phase Offset (Entry) PPO Polar Phase Ref (Entry) PPR Polar Real Offset (Entry) PRO I/O Test PRT Phase Slope Off PS0 Phase Slope On PS1 Phase Slope (Entry) PSL Math Term for Input R R radians RAD Resolution RBW Recall Instrument State RCL Recall Register n RCn Reference Level REF Return RET Return RET Return RET Return RET Reference Line Off RL0 Reference Line On RL1 Reference Position RPS Freq Swp Res 51 pts/span RS1 Freq Swp Res 101 pts/span RS2 Freq Swp Res 201 pts/span RS3 Freq Swp Res 401 pts/span RS4 radians/span RSP Source Amplitude SAM Save Instrument State SAV Scale SCL Store Data Reg 1 SD1 Store Data Reg 2 SD2 Store Data Reg 3 SD3 Store Data Reg 4 SD4 Service Diagnostics Menu SDG seconds SEC Seconds SEC Frequency, Source Frequency SFR Source Leveling Off SL0 Settling Time Off SL0 Source Leveling On SL1 Settling Time On SL1 Confidence Test Menu SLF Sweep Mode, Continuous SM1 Sweep Mode, Single SM2 Sweep Mode, Manual SM3 Sweep Mode SMD Sweep Time, Step Time (Entry) SMT S-Parameters Off SP0 S-Parameters ON SP1 Special Functions SPC Frequency, Sweep Resolution SRL Send SRQ SRQ Software Revision Message SRV Sweep, Linear ST1 Sweep, Alternate ST2 Sweep, Log ST3 Sweep, Amplitude ST4 Sweep, CW ST5 Sweep, Discrete ST6 Confidence Test Channel A STA Confidence Test Channel B STB Store and Display STD Settling Time Entry STE Sweep Time STM Store Data STO Confidence Test Channel R STR Sweep, Direction DOWN SUD Sweep, Direction UP SUP Save State in Register n SVn Sweep Time, (Entry) SWT Synthesizer Diag Off SY0 Synthesizer Diag On SY1 Trace 1 Linetype (Entry) T1L Trace 1 Pen Number (Entry) T1P Trace 2 Linetype (Entry) T2L Trace 2 Pen Number (Entry) T2P Store UD to D1 TD1 Store UD to D2 TD2 Store UD to D3 TD3 Store UD to D4 TD4 Free Run TG1 Line Trigger TG2 External Trigger TG3 Immediate TG4 Take Measurement TKM Trace Memory Test TMT Trace 1 TR1 Trace 2 TR2 Sweep Trigger TRG.Sweep Reset Reset TRG/RST Trigger Mode TRM Test Forward TSF Rest Reverse TSR User Defined Input UD1 User Defined Store UDS Define Function F1 UF1 Define Function F2 UF2 Define Function F3 UF3 Define Function F4 UF4 Define Function F% UF5 microseconds USC Microseconds USC microVolts UV Volts V Zero Marker ZMK
HP3577 Display Formats   Function HP-IB Code Trace 1 TR1 Trace 2 TR2 Display Function DSF Log Magnitude DF7 Linear Magnitude DF6 Phase DF5 Polar DF4 Real DF3 Imaginary DF2 Delay DF1 TraceOff DF0 Delay Aperture Menue DAP Aperture 0.5% of Span AP1 Aperture 1.0% of Span AP2 Aperture 2.0% of Span AP3 Aperture 4.0% of Span AP4 Aperture 8.0% of Span AP5 Aperture 16% of Span AP6 Return RET Input INP Input x= R,A,B Inx Input =A/R IAR Input=B/R IBR Input=D1 ID1 Input=D2 ID2 Input=D3 ID3 Input=D4 ID4 User Defined Input UD1 Input = S11 I11 Input = S21 I21 Input = S12 I12 Input = S22 I22 Copy Input CPI Test Forward TSF Rest Reverse TSR Scale SCL Autoscale ASL Reference Level REF Scale/DIV DIV Reference Position RPS Reference Line Off RL0 Reference Line On RL1 Copy Scale CPS Phase Slope (Entry) PSL Phase Slope Off PS0 Phase Slope On PS1 Polar Full Scale (Entry) PFS Polar Phase Ref (Entry) PPR Smith Chart Off GT0 Smith Chart On GT1 Marker Position (Entry) MKP Marker Off MK0 Marker On MK1 Zero Marker ZMK Marker Offset Off MO0 Marker Offset On MO1 Marker Offset (Entry) MK0 Marker Offset Freq (Entry) MOF Marker Offset Map (Entry) MOA Marker Coupling Off CO0 Marker Coupling On CO1 Polar Mag Offset (Entry) PMO Polar Phase Offset (Entry) PPO Polar Real Offset (Entry) PRO Polar Imag Offset (Entry) PIO Polar Marker Units (Real/Imag) MRI Polar Marker Units (Mag/Phase) MMP Marker MKG MKR-Reference Level MTR MKR-Start Frequency MTA MKR-Stop Frequency MTB MKR-Center Frequency MTC MKR Offset Span MOS MKR-Max MTX MKR-Min MTN MKR-Target Value MTV MKR-Right for Target MRT MKR-Left for Target MLT MKR-Full Scale MTP MKR-Polar Phase Ref MPF Store Data STO Store Data Reg 1 SD1 Store Data Reg 2 SD2 Store Data Reg 3 SD3 Store Data Reg 4 SD4 Store and Display STD User Defined Store UDS Store UD to D1 TD1 Store UD to D2 TD2 Store UD to D3 TD3 Store UD to D4 TD4 Measurement Calibration CAL Measurement Cal Normalize NRM Measurement Cal Short NRS Measurement Cal Partialize CPR Measurement CAL Full CFL Measurement CAL Continue CAL CGO Define Math DFN Define Math, Constant K1 Real (Entry) KR1 Define Math, Constant K1 Imaginary (Entry) KI1 Define Math, Constant K2 Real (Entry) KR2 Define Math, Constant K2 Imaginary (Entry) KI2 Define Math, Constant K3 Real (Entry) KR3 Define Math, Constant K3 Imaginary (Entry) KI3 Define Function DFC Define Function F1 UF1 Define Function F2 UF2 Define Function F3 UF3 Define Function F4 UF4 Define Function F% UF5 Math Term for Input R R Math Term for Input A A Math Term for Input B B Math Term for constant K Math Term for Function F Math Bracket ( Math Function Plus + Math Function Minus - Math Function Multiply * Math Function Divide / Math Bracket ) Data Entry Commands   Increment (Up Arrow) IUP Increment Down (Down Arrow) IDN Continouous Entry (knob) Off CE0 Constinuous Entry (knob) Onn CE1 Entry Off HLD Display Format Suffix Units   dBm DBM dBV DBV dB Relative DBR Volts V milliVolts MV microVolts UV nanoVolts NV degrees DEG degrees/span DSP radians RAD radians/span RSP seconds SEC milliseconds MSC microseconds USC nanoseconds NSC percent % exponent E SOURCE   Sweep Type   Sweep, Linear ST1 Sweep, Alternate ST2 Sweep, Log ST3 Sweep, Amplitude ST4 Sweep, CW ST5 Sweep, Discrete ST6 Sweep, Direction UP SUP Sweep, Direction DOWN SUD Sweep Mode SMD Sweep Mode, Continuous SM1 Sweep Mode, Single SM2 Sweep Mode, Manual SM3 Manual Frequency Entry MFR Manual Amplitude Entry MAM Marker to Manual MTM Sweep Time STM Sweep Time, (Entry) SWT Sweep Time, Step Time (Entry) SMT Sweep Time, Sample Time MSR Frequency FRQ Frequency, Source Frequency SFR Frequency, Start Frequency FRA Frequency, Stop Frequency FRB Frequency, Center Frequency FRC Frequency, Span FRS Frequency, FRC Step Size (Entry) CFS Frequency, Sweep Resolution SRL Freq Swp Res 51 pts/span RS1 Freq Swp Res 101 pts/span RS2 Freq Swp Res 201 pts/span RS3 Freq Swp Res 401 pts/span RS4 Return RET Full Sweep FSW Freq Step Size FST Amplitude AMP Source Amplitude SAM Amp Step Size AST Clear Trip, Source CTS Start Amplitude (Entry) AMA Stop Amplitude (Entry) AMB Steps/Sweep Menu NST Number of Steps =6 NS1 Number of Steps = 11 NS2 Number of Steps = 21 NS3 Number of Steps = 51 NS4 Number of Steps = 101 NS5 Number of Steps = 201 NS6 Number of Steps = 401 NS7 Return RET Full Sweep FSW Trigger Mode TRM Free Run TG1 Line Trigger TG2 External Trigger TG3 Immediate TG4 Sweep Trigger TRG.Sweep Reset Reset TRG/RST RECEIVER   Resolution RBW Resolution BW 1 Hz BW1 Resolution BW 10 Hz BW2 Resolution 100 Hz BW3 Resolution 1kHz BW4 Auto Bandwidth Off AU0 Auto Bandwidth On AU1 Average AVE Averaging Off AV0 Average N = 4 AV1 Average N = 8 AV2 Average N = 16 AV3 Average N = 32 AV4 Average N = 64 AV5 Average N = 128 AV6 Average N = 256 AV7 Attenuation ATT Attenuation R = 0 dB AR1 Attenuation R = 20 dB AR2 Attenuation A = 0 dB AA1 Attenuation A = 20 dB AA2 Attenuation B = 0 dB AB1 Attenuation B = 20 dB AB2 Impedance R = 50 Ohms IR1 Impedance R = 1 M Ohm IR2 Impedance A = 50 Ohms IA1 Impedance A = 1 M Ohm IA2 Impedance B = 50 Ohms IB1 Impedance B = 1 M Ohm IB2 Clear Trip, Receiver CTR Length LEN Length R (Entry) LNR Length R Off LR0 Length R On LR1 Length A (Entry) LNA Length A Off LA0 Lentth A On LA1 Length B (Entry) LNB Length B OFf LB0 Length B On LB1 Length Step Size LNS Receiver Suffix Units   Meters MET Centimeters CM Seconds SEC milliseconds MSC Microseconds USC Nanoseconds NSC Exponent E Instrument Status   Special Functions SPC Confidence Test Menu SLF Confidence Test Channel R STR Confidence Test Channel A STA Confidence Test Channel B STB Return RET Beeper Off BP0 Beeper On BP1 Service Diagnostics Menu SDG Source Leveling Off SL0 Source Leveling On SL1 Settling Time Off SL0 Settling Time On SL1 Synthesizer Diag Off SY0 Synthesizer Diag On SY1 Display Test Pattern DTP Trace Memory Test TMT Fast Processor Test FPT I/O Test PRT More Serv Diag Menu MOR Display Memory Test DST Software Revision Message SRV S-Parameters Off SP0 S-Parameters ON SP1 Save Instrument State SAV Save State in Register n SVn Recall Instrument State RCL Recall Register n RCn Instrument Preset IPR Plot Menu PLM Plot All PLA Plot Trace n PLn Plot Graticule PLG Plot Characters PLC Plot Trace Marker n PMn Configure Plot Menu CPT Trace 1 Linetype (Entry) T1L Trace 2 Linetype (Entry) T2L Trace 1 Pen Number (Entry) T1P Trace 2 Pen Number (Entry) T2P Graticule Pen Number PGP Pen Speed Fast (Max) PNM Pen Speed Slow PNS Set Plot Config to Default PLD Plotter Address (Entry) HBP HP-IB Only Commands   Settling Time Entry STE Dump Register x (x= A, B, R, D1, D2, D3, D4) DRx Dump Trace n DTn Dump Marker n DMn Dumper Marker n Position MPn Dump State (learn mode out) LMO Dump Status DMS Dump Average Number DAN Dump Key or Knob DKY Dump Characters DCH Dump Instrument ID ID? Load Register x (X= A B R) LRx Load Register x (X= D1 D2 D3 D4) LDx Load State (learn mode in ) LMI Graticule Off GR0 Graticule On GR1 Characters Off CH0 Characters On CH1 Annotation Off AN0 Annotation On AN1 Annotation Clear ANC Menu Off MN0 Menu On MN1 Menu Clear MNC ASCII Data Format FM1 64 Bit IEEE Data Format FM2 32 Bit HP 3577B Binary FM3 Bus Diagnostics Mode Off BD0 Bus Diagnostics Mode On BD1 Enter Menu (User Defined) ENM Enter Annotation ENA Enter Graphics ENG Clear Keyboard Buffer CKB Take Measurement TKM Error Reporting Mode n Ern Send SRQ SRQ